WALKERS Stoves Richmond Deluxe S1100 DF GTG Range Cooker Instruction Manual

WALKERS Stoves Richmond Deluxe S1100 DF GTG Range Cooker

BEFORE INSTALLATION

LEVELLING YOUR COOKER

1.  Place a spirit level on a baking sheet onto an oven shelf.
2.  The cooker is fitted with levelling feet (1). Level your cooker to your desired height using the levelling feet at the front and rear of the cooker.

Rear of cooker

REAR WHEELS (IF FITTED)
Adjustment of the wheel height can be made with a screw driver, through the hexagonal hole in the front plinth.

FITTING THE PLINTH (IF APPLICABLE)

1.  Ensure the appliance is raised to a height of 915 mm or above using adjusting feet (A) before beginning.
2.  Open the appliance doors and loosen screw (C), do not remove the screw entirely. If your appliance has a storage drawer at the bottom, you access the screws through holes located at the base of the drawer after lifting the mat.
3.  Fit plinth (B) and secure using screw (C).

FITTING THE TOWEL RAIL (IF APPLICABLE)

On the towel rail there are two holes, top (A) and bottom (B), these holes have corresponding holes on the fascia at each end.
The 2x longer screws are designed for the top hole (A), whereas the remaining screw just goes through the bottom hole (B). Both screws are M6 screws. Using the Allen key provided, tighten the screws making sure that the towel rail is flush to the fascia, but not over tightened.

DIMENSIONS AND CLEARANCES

CUPBOARD / HOOD CLEARANCES

• A Nominal width of the hob B Wall Unit
• C Worktop
• No shelf or overhang of combustible material should be closer than 650 mm above the hob.
• If your appliance has a side opening door, we recommend a side clearance of 60 mm to allow the oven door to fully open, if placed up to a wall or cabinetry.
• The cooker must have a side clearance above hob level of 90mm up to a height of 400 mm.
• This cooker may be fitted flush to the base units of your kitchen.

STABILITY BRACKET
If the cooker is fitted with a flexible connection, a stability bracket should be fitted to engage in the back of the cooker. A stability bracket can be bought from your local supplier.

A stability bracket can be fitted as follows:

1.  Place the cooker in the position and draw a PENCIL LINE level with the front edge.
2.  Mark the centre of the cooker to give the CENTRE LINE for the bracket.
3.  Remove the cooker and mark off 450 mm from the PENCIL LINE to locate the front edge of the lower bracket.
4.  Fix the bracket to the floor. Measure from floor level to engagement edge in the back of cooker and add 3 mm.
5.  Assemble the underside of the top part of the bracket to this height.

Rear wall

CONNECTION TO THE ELECTRICITY SUPPLY

6 WARNING: This appliance must be earthed.
This appliance must be fitted to a switch providing all pole disconnection with a minimum contact separation of 3 mm.
6 The terminal block screws and clamps can be damaged by excessive tightening and untightening. DO NOT USE POWER TOOLS!

1.  Gain access to the mains terminal by removing the terminal block cover at the rear of the appliance.
2.  Connection should be made with a suitable flexible cable.
3.  First strip the wires then push the cable through the cable clamp.
4.  Connect the cable to the terminal block and tighten the cable clamp screws – see diagram.
5.  Refit the terminal box cover.
6.  Sufficient cable should be used to allow the cooker to be pulled out, but must hang clear of the floor so it does not become twisted or trapped when the cooker is pushed back.
   SINGLE PHASE CONNECTION (230 V ~50 HZ)
7.  Connect cable to the terminal block:
   •  L to terminal 3
   •  N to terminal 6
   •  Earth to terminal
8.  Ensure shorting links are fitted between terminals 1-2, 2-3, 4-5 and 5-6.
9.  Ensure all screws are fully tightened.

THREE PHASE CONNECTION (230/400 V 3N ~50 HZ)

1.  Connect cable to the terminal block:
   •  L1, L2 and L3 to terminals 1, 2 and 3
   •  N to terminal 5
   •  Earth to terminal
2.  Remove shorting links 1-2 and 2-3.
3.  Ensure shorting links are fitted between terminals 4- 5 and 5-6.
4.  Ensure all screws are fully tightened.

CONNECT TO THE GAS SUPPLY

• The inlet to the cooker is ½” BSP internal situated at the rear right corner. Fit the bayonet connection. This should be located so as to ensure that the flexible connector hose does not kink.
• 6 Under no circumstances should the flexible connector be allowed to come into contact with the vertical oven flue tubes on the rear of the appliance.
• Use a 900 mm – 1125 mm length of flexible connector.
• Ensure that all pipework is of the correct rating for both size and temperature.
• Flexible connections should comply with the relevant national regulations and codes of practice in force in the country where it is intended to be installed. Parts of the appliance likely to come into contact with a flexible
• connector have a temperature rise of less than 70 °C.
• After installation, make sure all connections are gas sound.

COMMISSIONING

BURNER AERATION
All burners have fixed aeration and no adjustment is possible.

PRESSURE SETTING
Pressure test point: Use the oven injector.

HOB BURNER
Turn the control knob to the ‘FULL ON’ position, wait a second before pressing the ignition switch or holding a lighted match or taper to the burner. Hold the control knob in for 15 seconds. Do not hold the control knob in for longer than 15 seconds. If the burner fails to light within this time, release the control knob and wait one minute before attempting further ignition.

CHECK THE OPERATION OF ELECTRICAL COMPONENTS

• Clock Programmer/Minute Minder
• Check functions as described in the User Guide.
• Oven light & Convection fan
• Open the main oven door. Turn the main oven control knob to the defrost setting. Check the oven light and convection fan both come on. Turn control knob back to ‘OFF’ position.
• Cooling Fan
• Turn the top oven control knob to the full power setting.
• Check that the cooling fan operates. Turn control knob back to ‘OFF’ position and check cooling fan switches off immediately.
• 4 Note: If the cooker does not perform correctly, inform the customer of the problem and put a warning notice on the cooker. If the problem is dangerous, then disconnect the cooker. If there is a fault, then the customer should
• be advised to contact the manufacturer’s local service organisation or the retailer.
• 4 Before leaving the installation hand over the User Guide to the customer

Documents / Resources

WALKERS Stoves Richmond Deluxe S1100 DF GTG Range Cooker [pdf] Instruction Manual Stoves Richmond Deluxe S1100 DF GTG Range Cooker, DF GTG 100 110 cm

References

• User Manual