EMMO Caofen F80-OR-30 Dirt Bike User Manual
EMMO Caofen F80-OR-30 Dirt Bike

Warning Icon WARNING

  • Please read this manual carefully.
  • This manual contains important safety information.
  • Minors under the age of 16 are not allowed to drive this electric motorcycle.

Introduction

Congratulations on your choice to acquire the EMMO CAOFEN-F80 series electric motorcycle, which incorporates years of technological advancements in alloy material research, core component manufacturing, and integrated electric drive. As the proud owner of this cutting- edge electric motorcycle, you can expect long- lasting enjoyment with proper maintenance. This manual aims to provide you with a comprehensive understanding of the model’s fundamental features and operational skills. Should you encounter any operation or maintenance concerns not addressed in this manual, please feel free to reach out to EMMO Manufacturing Company or your local distributor for assistance.

Important safety information:

  • This instruction manual contains important information, precautions, warnings and hazard notes for the use of the vehicle. The illustrations in the manual may differ slightly from the vehicle in detail, but the principles described are the same.
  • EMMO CAOFEN-F80 electric motorcycle has always maintained high-quality standards, due to the unremitting pur- suit of product quality and the continuous indepth research and improvement of product design. The information provided may not be the same as your ve. hicle information without further notice.
  • For more detailed information about EMMO CAOFEN-F80 and the use and maintenance manual, please enter the EMMO official website: WWW.EMMO.CA ; or scan the EMMO official QR code on the last pag

Important Information 

Failure to observe the contents of the manual may lead to serious injury or death!
This manual and its important information are marked as follows:

Safety warning signs mean attention, careful, vitally

Warning Icon important

  • Failure to comply with warning signs may cause fatal inFailure to comply with warning signs may cause fatal injury or death to F80 electric motorcy cle drivers, bystanders, maintenance or mainte- nance personnel.
  • Warning means that precautions should be taken to avoid damage to the vehicle.

Careful
Tips provide you with important information for easier operation

Open steps and Assemble

Open the Carton:

  1. Please check whether the outer packaging (as shown in the upper right picture) is complete; then shear the packing belt and remove the packing carton, as shown in the lower right picture.
  2. Relax straps 6
  3. Loosen front axle 1, locking nut, and then pull out the front axle
  4. Remove the packaging bottom tray and lower the side stand

Assemble

  1. Front axle and lock nut
  2. Front fender bracket
  3. Accessory
  4. Handle bar
  5. Front turning signal
  6. Front tightening straps
  7. Front rim and tire

Assemble front wheel:

Parts Ready: Front axle, front axle lock nut, 2 pieces front wheel bush
Assemble

  1. First install a bush on the left (From the drivers’ view) of the front wheel, place the big head on the front wheel and small head toward the shock absorber, and then take the front axle little head from shock on the left to right across the suspension, front wheel bushing, the front wheel, wheel bushing, shock absorb, and then put the former wheel lock, nut lock and then in turn lock before cutting on the front wheel lock screw tied.
  2. Front brake installation: remove the yellow fixed stop plat hydraulic brake pump, clamp the brake disc on the front hub into the brake clamp of the lower brake pump, pinch the right brake handle, tighten the installation bolt of the lower pump, and then release the handle.
    1. front wheel lock nut
    2. front wheel bushing
    3. front wheel locking
    4. front wheel bushing
    5. front fork
    6. Front wheel shaft
    7. front axle Assy.

Warning Icon Warning

Grease on the brake disc will reduce the braking effect, please always keep the brake disc grease free, please use detergent to clean the brake disc when necessary

Assemble of Handlebar

Assemble of Handlebar

  1. Handle bar
  2. Handlebar seat
  3. handle bar locking bolts 4-M6*20
  4. Handle bar locking cover

Handlebar fixing:

  1. Put the handle bar 1 into the handle seat 2 slot and make sure that the scale on the handlebar is evenly distributed
  2. Cover the handlebar locking cover 4, and evenly lock the 4 bolts without loosening

Assemble Speedometer and front Turn signal

Assemble Speedometer

  1. Handlebar
  2. Speedometer
  3. Speedometer rubber pad
  4. Front turn signal
  5. Turn signal lock nut and sleeve
  6. Headlight bracket
  7. Speedometer wire harness and rubber sleeve
  8. Headlight
  9. Speedometer lock nut M6
  10. Speedometer rubber pad

Speedometer and front turn signal

  1. Place the meter correctly according to the picture. After install- ing the anti-vibration rubber pad, lock the ball nut, plug in the meter wiring harness, and cover the waterproof rubber cover.
  2. Install the turn signal according to the picture, lock the nut, and cover the decorative rubber cover.

Speedometer and indicator light

Speedometer and indicator light

  1. Turn indicator
  2. Battery level indicator
  3. Power gear display
  4. Fault warn light
  5. Current gear position indicator
  6. Running speed
  7. Speed unit
  8. Battery warning light
  9. Running lights
  10. Energy recovery
  11. Total mileage display
  12. Entertainment mode
  13. Switch button
  14. Mileage
  15. Gear position

Tip: The F80 electric motorcycle you buy may be different from the description in this manual

Speedometer indicator

Press the remote control button, the LCD screen lights up, and the speed- ometer displays the last shutdown information mode.

  1. Far light, the initial setting of the speedometer is set as the daytime running light, press the upper light button on the left brake handle, and turn on the far light.
  2. The front, rear, left and right turn indicators in- dicate that when the steering switch on the left brake handle is pushed to the left, the front and rear turn signals on the left will flash; when the steering switch is pushed to the right, the front and rear turn signals on the right will flash.
  3. Entertainment mode display:Press and hold the switch on the right brake for 3 seconds. When it is off, there is no traction control, and a con- stant value indicates that there is traction control.
  4. S power gear display: the S light does not blink, corresponding to D gear and 1 gear, slow flash 2 gear, fast flash 3 gear.
  5. D Current motion mode: Press the N/D button on the right brake handle to control the entering sports D gear. The light is either always on or off. If it is always on, it means that it has entered the current gear and the vehicle can be driven. If it is off, it means the vehicle is in the neutral position.
  6. Energy recovery indicator light: Steady on: The energy recovery is in the auxiliary braking mode. After the braking signal is detected, energy recovery is added after a delay of 20 milliseconds or when the vehicle speed drops by 10%.
    Flashing: Energy recovery occurs during the throttle release phase. Off: Energy recovery is turned off.
  7. Driving READY light: The one-key start button controls the light to turn on or off. The vehicle can be driven when it is always on, and the vehicle cannot be driven when it is turned off.
  8. Off: Sufficient power. Steady on: Insufficient power. Flashing: Low power, the battery needs to be charged as soon as possible.

Warning Icon Warning

If you find that the indicator light is on or flashing after the vehicle is powered on, you may not be able to drive normally if you continue to use the motorcycle; if you find that the indicator light is on or flashing while driving, please stop using the motorcycle immediately; lighting or flashing indicates that your mo torcycle has broken down, please check the fault code displayed on the instru ment according to the description in this manual, and consult the local EMMO authorized dealer as soon as possible.

Warning Icon Warning

Please do not flush the speedometer directly with high pressure water. Please do not wipe the speedometer with organic solvents such as gasoline and alcohol, otherwise it will cause partial cracks or discoloration of the meter.

Directional combination switch 

Left handlebar switch combination
Directional combination switch

  1. Headlight switch button
  2. Left and right turn signal switch
  3. Horn button

Right handlebar switch combination 

Right handlebar switch

  1. Entertainment mode switch
  2. Energy recovery switch
  3. Switch between gear and neutral
  4. Gear switch button

Info: entertainment mode activation: please press and hold the button for 3 seconds

Front and rear shock adjustment (Right and left shock)

Adjusting the preload of front and rear shock absorber is to adapt to different drivers, loads, driving mode and road environment, in order to achieve the best driving performance of the motorcycle, and avoid damage to the front fork, rear shock absorber and body.

Front left shock absorption (spring preload):

  1. Spring preload adjusting knob
  2. Vent screw
  3. 10mm wrench or sleeve

adjustment

  1. Rotate the adjusting knob in the direction of a to increase the spring preload value
  2. Rotate the adjusting knob in the direction of b to reduce the spring preload value
  3. The rotation of spring preload adjusting knob can be adjusted manually or by 10mm wrench or a socket
  4. The adjustable height of spring preload is 12.5mm. The height of the spring preload adjust- ment knob can be raised and lowered by one turn of 1.25mm

Front right shock (return damping)

  1. Return adjusting button
  2. Bleed screw

Front right shock

  1. Rotate the recovery adjustment button in the direction of A to increase the recovery damping
  2. Rotate the recovery knob in the direction OF B to reduce the recovery damping

Front and rear shock adjustment.

Compression adjustment button

adjustment

  1. Rotate the compression adjusting knob in the direction of a to increase the compression damping
  2. Rotate the compression adjusting knob in the direction b to reduce the compression damping

Return damping regulation

adjustment

  1. Return adjusting button
  2. 8mm inner hexagon wrench
    1. Rotate the recovery adjustment button in the direction of a to increase the re- covery damping
    2. Rotate the recovery knob in the direc- tion of b to reduce the recovery damping
    3. the rotation of the adjustment button can be manually adjusted and 8mm inner hexagonal wrench two ways of adjust.

Compression damping regulation

adjustment

  1. compression adjust- ment button
    1. Rotate the compression adjusting knob in the di- rection of A to increase the compression damping
    2. Rotate the compression adjusting knob in the di- rection B to reduce the compression damping

Front and rear shock adjustment (adjusted shock assembly)

Spring preload

  1. Lock nut
  2. Spring preload adjusting nut
    1. Rotate the adjusting nut in the direction of a to increase the spring preload value
    2. Rotate the adjusting nut in the direction b to reduce the spring preload value
      adjustment

Spring preload
adjustment

  1. Special wrench

Locking torque of locking nut: 35 Nm

Warning Icon Warning

Please adjust preload, recovery damping and compression damping appro priately according to riding needs; Please do not blindly adjust the preload of shock absorption, improper adjustment results will make you feel un- comfortable or weaken your ability to control the vehicle.

Warning Icon Note:

Special tools are required for preload of shock absorber springs after adjustment. If adjustment is required, please use your local EMMO authorized distributor to provide such services for you.

Vehicle identification
Vehicle.

  1. Vehicle Plate 2.
  2. VIN NO.
  3. Motor model and factory No

Front Part
Front Part

  1. Headlight
  2. Speedometer
  3. Right brake lever
  4. Right hand grip
  5. Right speed control switch
  6. Handlebar
  7. steering dust cover
  8. One-button starter
  9. Rear view Mirror base
  10. Rear view Mirror
  11. Left switch assemble
  12. Left brake lever
  13. Front tire
  14. Front Rim Assy.
  15. Front brake disc
  16. Front brake caliper
  17. Front mud guard
  18. Front shock absorber
  19. Horn
  20. Battery pack
  21. Battery bottom protective cover
  22. Chain
  23. Rear damping
  24. Rear wheel
  25. Rear Rim
  26. Rear sprocket
  27. Rear fender rear section
    Left Side
    Left Side
    Right Side
  28. Rear guard bracket
  29. Rear brake disc
  30. Chain Adjuster
  31. Rear brake caliper
  32. Rear fork
  33. Rear guard front part
  34. Taillight
  35. Seat bracket
  36. Seat
  37. Frame
  38. Steering
    Right Side
    Frame Inside
    Frame Inside

    Chain caliper
  39. Motor
  40. Controller
  41. Alarm
  42. DCDC converter

Operation and driving of EMMO CAOFEN-F80 electric motorcycle Step to start the vehicle:

  1. Turn on the battery switch, and the power switch indicator light is on.
  2. press the alarm switch. The speedometer lights up and the ve- hicle enters the self-test state.
  3. Fold up the side support and press start button, the speedome- ter will display the READY light steady on and start normally
  4. Press the N/D button on the right brake handle to enter motion D gear, and the speedometer D gear light will light up.
  5. Turn the right speed control handle to drive normally.

Warning Icon Warning
When the outdoor temperature is below 0°C, the low temperature protection of the battery system may be triggered. Please charge the battery before using it; otherwise, the vehicle may not run normally. When the meter displays a fault code, please check the fault code displayed on the meter according to the description in this manual, and consult the local EMMO dealer for treatment as soon as possible.

Warning Icon Dangerous
When the speedometer shows D, at this time the vehicle is in the forward state, turn the right speed control turn the vehicle will run, net familiar with the vehicle operation process if the rotation speed control turn is very large, the vehicle will suddenly move forward at high speed, may lead to personnel injury or vehicle damage: Therefore, when refueling for the first time, please be sure to concentrate on the smooth and light rotation of the speed control, and the left and right index finger and middle finger are placed on the brake handle to prevent the speed control rotation is toe large and the vehicle can suddenly brake at high speed

Steps to turn off the vehicle:

  1. After the vehicle stops, press the N/D button on the right brake handle, and the speedometer shows that the D light goes out and enters neutral, and the vehicle no longer walk.
  2. The braced side bracket is in parking state, and the READY light is off.
  3. Press the alarm button to power off and turn off all electrical equipment
  4. Turn off the battery switch. 18

Side Stand
Side Stand

  1. . Chain tensioner
  2. 2. standby switch
  3. 3. side stand

This electric motorcycle is designed with a side support parking system. The side support extinguishing fire switch is a safety design, which is a part of the starting circuit. When the side support in in the parking state, the READY light will be off, and only when the side sup port is folded up, the READY light will be on.

warning
When the speedometer lights up, it may be impossible to directly power off the alarm key, so we can directly turn off the battery switch. In this case, please check the fault code displayed on the instrument according to the description in this manual, and consult the local EMMO dealer for treatment as soon as possible. The temperature of the motor may be very high after the vehicle is stopped, please cool it before touching it

Dangerous
The failure of the speed control knob will make the switch difficult to operate. If you want to speed up or slow down, but it is difficult to use, it may cause serious injury or death. Please check the switch handle operation before starting. If the operation is not smooth or stuck, check the reason before riding. If you are unable to solve the problem, please consult your local EMMO distributor.

Dangerous
Deceleration in the process of high-speed driving, such as just use the front brake or rear brake, the vehicle is easy to skid and out of control.Both front and rear brakes must be used equally.

Driving Precautions

  1. Try not to carry occupants. If the user must carry it, any occupant must be very familiar with the particularity of electric motorcycle driving, because the position of the occupant is not suitable. Sudden movement during driving may affect the handling of the vehicle; therefore, we remind the occupants to keep their seats as stable as possible while driving, and not to affect the driver’s handling. Animals cannot be carried on motorcycles.
  2. In order to reduce the impact on the center of gravity of the motorcycle, all luggage on the motorcycle must be as low as possible; the weight of the luggage must also be evenly distributed on both sides of the motorcycle. Luggage protruding too far behind the motorcycle should be avoided.
  3. The luggage must be securely fixed on the motorcycle. Please make sure that the luggage cannot be moved before driving. When the motorcycle feels unstable while driving, the firmness of the luggage should be rechecked and readjusted if necessary.
  4. Do not carry heavy or bulky luggage. Overloading must affect handling and dynamic performance.
  5. Do not install accessories that reduce the perfor mance of this electric motorcycle and carry luggage that reduces the performance of the motorcycle, make sure that everything you do will not affect any lighting system, ground clearance, braking performance, roll angle, handling performance, tires Compression stroke, front reduction working stroke or other related driving performance of this electric motorcycle.
  6. The increased weight on the handlebar or front fork will affect the steering performance and cause unsafe driving factors.
  7. This vehicle cannot be converted into a three-wheeled motor cycle, and cannot be used for towing trailers or other vehicles. We will not be responsible for any damage or injury caused by the user’s selfrefitting of this vehicle. 8. It is forbidden to drive after taking medicine or drinking. Please wear suitable and genuine safety equipment: helmet, eye mask, face shield, gloves, boots, long-sleeved shirt or jacket, trousers. Maximum load: no more than 100kg including driver, luggage and accessories).

Note: The speedometer shows that the 1st gear is the lowest power output, and the starting is the most stable, and the 2nd and 3rd gears increase the power step by step; When the charging light is flashing and the power indicator is lower than 20%, please recharge it; the battery power protection strategy will limit the output power at 15%.

Charger Instructions

Overview
This smart charger is specially used to charge the power battery of CAOFEN vehicles. It uses a civil 10A or 16A socket power supply. The charging process is con- trolled by the charging program itself, and it stops au- tomatically when it is fully charged.

Product appearance diagram
Charger Instructions

small size and high power The charging speed is fast, and it can be charged to BM of the power in two hours at 20 °C;
automotive grade shock resistance durable;
six items security pro- tections Dedicated protection, over temperature protection, output short circuit, output reverse connection, output over-volt­age, output over-current protection
IP66 level protection Higher       protection,   higher        security,higher reliability;
CAN intelligent commu• nlcatio Real-time communication with the ye­hide to ensure controlled charging;
wide temperature range operating tem- perature It can work normally at -40 — 60 °C;
lightweight and porta- He design All aluminum alloy die-casting shell, light weight and good heat dissipation.
NO. item technical indicators note
1 operating temperature .40C “,+60C
2 Storage temperature .40C ^-+90C
3 relative humidity 5%”’95strong
4 protection class IP66

5 cooling method forced air cooling Pay attention to AC power
6 Input voltage Input frequency AC220V+15% malching.
7 AC90-140V AC 220v power supply is
strictly prohibited
8 50±2%

AC220V or 110v AC power supply should be selected according to the AC power supply (AC) voltage requirements indicated on the label at the bottom of the charger body, and the rated current of the corresponding charging socket should meet at least 10A (AC.

socket should meet at least 10A (AC). It is strictly focobidden to use AC220V power supply for AC110V (100V) special charger! Othervise, there may be serous security risks
Charging method
It should be charged in a cool, dry and ventilated places
When charging, the charger should be kept away from flaminable materi als, keep good ventilation and heat dissipation around the charger, and it is strictly forbidden to cover things on the charger
Press the battery switch to turn on the battery (the switch light is on);
Hold the DC output plug of the charger, insert it into the battery charging hase, and push the lock in to ensure that the charging head and the battery charging base are fully and tightly connected; 5.5 Insert the AC input line plug of the charger into the appropriate socket (make sure the plug and socket are fully, and reliably inserted), the charging indicator of the charger will turn green, about 35, the indicator will change from steady green to flashing red, and then the charger fan will automatically turn on and enter the charging state
When the battery is fully sharged, the sharger will automatically stop charging. At this time, the indicator light of the charger will turn solid green and the cooling fan will stop rotating. On the corresponding instrument of the vehicle, the battery level is displayed as 100%, and the flashing battery charging symbol disappears.
After charging, unplug the charger output plug from the battery and cover with a dustproof plastic cover. Then, remove the charger input play from the AC outlet.

Frequently Asked Questions and Instructions

NO. Phenomenon Problem Solution
1 charger, green light, not3cisarging The AC power voltage does not match the input AC voltage indicated on the labol of the charger. Replace with an AC outlet that matches the voltage
2 The charger output plug is not inserted into the battery or is not fully inserted Fully iraert the charger sutput (DC) plug ints the battery charging socket
3 Battery switch not tumed on Pross the switch, tam on the battery, and the switch light will tare on
4 charger does not match the bat tery Contact the dealer or factory for re placement.
5 The charger or battery temperature in too high It will be released naturally after the temperature is lowered to within 45°C
6 charging is slow Temperature below 5 It Change to an environment above 150 for charging or wait for the bat hery temperature to rise, the charger
7 The battery temperature is higher than 45°C the battery temperature drops.
8 Charger parent is running out of battery Check the AC outlet
9 No response from the charger, indi cating that the light is not an The charger itself is fauity Contact the seller or marudanturer.

Indicator status description

1 charging process the red light flashes once every 18 battery is below 90%
2 the green light flashes once every 15 battery 90%-100%
3 green light, always on. charging finished
4 instruction the red light flashes ence every 25 battery failure
5 the green light flashes once every 35 charger fallure
6 the red and green light flash al- tenately. Input failure

Safety precautions

  • Ensure that the charger vent and the space where it is lo- cated are kept unobstructed to prevent the charger from overheating.
  • When charging, keep away from heat sources and flamma- ble materials, and charge in a cool, dry and ventilated place. > Ensure that the AC power supply voltage and current are consistent with the allowable input voltage and current of the charger.
  • For the sake of safety and electromagnetic compatibility, the three-pin plug of the charger needs to use a socket with a grounding wire. > The AC power supply line should not be too long or too thin, so as not to affect the normal charging of the charger.
  • The charger should be placed on a level surface, and the radiator should be kept vertical to ensure good heat dissipa tion.
  • If the charger is found to be abnormal or damaged during the charging process, please unplug the power plug and charger interface immediately, and contact the supplier.
  • It is strictly forbidden to disassemble the charger by your self, and there is a danger of electric shock if you open the cover of the charger at will.
  • Prevent damage to the charger wiring harness. If the wiring harness is found to be worn or damaged, please re- place it immediately.
  •  It is recommended that users perform dust removal treat- ment on the charger shell at least half a year.
  • The power input end of the charger must be equipped with over-current protection devices (such as fuses, AC circuit breakers).

Warning Icon Notice

For more information and maintenance manual of EMMO CAOFEN-F80 please visit EMMO’s official website: www.emmo.ca or scan the below QR code to learn more
QR Code

EMMO Logo

Documents / Resources

EMMO Caofen F80-OR-30 Dirt Bike [pdf] User Manual
Caofen F80-OR-30 Dirt Bike, Caofen F80-OR-30, Dirt Bike, Bike

References

Leave a comment

Your email address will not be published. Required fields are marked *