spl-LOGO

spl Performer s800 Stereo Power Amplifier

spl-Performer-s800-Stereo-Power-Amplifier-PRODUCT

Product Information

  • Specifications
    • Output power: 2 x 285 W (4 ohms), 450 W (8 ohms in bridge mode)
    • Output voltage: 120V DC Audio Rail
    • Damping factor: 18
    • Frequency response: 20 Hz – 20 kHz
    • Signal-to-noise ratio: 19 dB
    • Total harmonic distortion: < 0.01%
    • Internal Voltage: AC, Hz / Hz, P max. VA
    • Power supply: ~ V AC / ~ V AC
    • Dimensions: (incl. feet)
    • Weight: 20 lbs
  • Getting Started
    • Before using the Performer s800, please read the Quickstart guide provided with the product. You can also download the Quickstart guide here.
  • Front View
    • Speaker Outputs
      • The Performer s800 is equipped with speaker outputs for connecting your loudspeakers. Please ensure that the minimum load requirements are met for optimal performance.
    • Bridge Mode
      • In Bridge Mode, use the INPUT L only. Set the L and R INPUT TRIMS at the same value.
    • Protection Circuits
      • The Performer s800 features built-in protection circuits to safeguard against potential issues.
    • DC Protection
      • The amplifier has DC protection to prevent any DC voltage from reaching the loudspeakers, which can cause damage. If the DC protection is triggered, check your connections and ensure there are no short circuits.
    • Overheating Protection Circuit
      • The amplifier is equipped with an overheating protection circuit to prevent damage due to excessive heat. If the amplifier overheats, it will automatically shut down. Ensure proper ventilation and avoid blocking the cooling vents.
  • FAQ
    • Q: Can I use the Performer s800 in bridge mode with different input trim values for L and R?
    • A: No, in bridge mode, the L and R INPUT TRIMS must be set at the same value for optimal performance.
    • Q: What is the minimum load requirement for the Performer s800 in bridge mode?
    • A: The minimum load requirement in bridge mode is not specified in the user manual. Please refer to the manufacturer’s guidelines or contact customer support for more information.

Getting started

Read thoroughly and follow the instructions as well as the security advice of the Quickstart which is enclosed in the scope of delivery! You can also download the Quickstart here.

  • By pressing the spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (2)Button you get to the table of contents.
  • By pressing the spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (3) Button you get to the front view of the unit.
  • By pressing the spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (4) Button you get to the rear view of the unit.
  • By pressing the spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (5) Button you get to the previous content.

Front view

spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (6)

Rearview (Stereo Mode)

spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (7)

Rearview (Bridge Mode)

spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (8)

Voltaire – 120V Rail Technology

  • Voltaire is the synonym for our 120V Rail Technology within the Professional Fidelity series.
  • The audio signals are processed with an unequalled +/-60V DC, which corresponds to twice that of discrete operational amplifiers and four times that of semiconductor operational amplifiers.
  • Voltaire Technology reaches outstanding technical and sonic performances.
  • Technically especially in terms of dynamic range and headroom and sonically especially in reproducing the finest details and delivering a totally relaxed sounding audio experience. Music sounds absolutely natural.

Comparisons

  • These diagrams show how our VOLTAiR Technology compares to other circuits.
  • The direct relation between the operating level and the maximum level is fundamental for the classification: the higher the operating level, the higher the maximum level a circuit can handle.
  • And since virtually all essential acoustic and musical parameters depend on this relation, a higher operating voltage also has a positive impact on the dynamic range, distortion limit and signal-to-noise ratio.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (9)
  • Do bear in mind that dB scales do not represent linear but rather exponential increases.
  • A 3 dB increase corresponds to doubling the acoustic power, +6 dB corresponds to twice the sound pressure level, and +10 dB corresponds to twice the perceived loudness.
  • When it comes to volume, the VOLTAiR Technology exhibits a performance, in regard to maximum level and dynamic range, that is twice that of common components and circuits given that its values are approximately 10 dB higher.
  • THD measurements show a difference of more than 3 dB compared to the OPA134 at 36 V — in terms of sound pressure level, which corresponds to an improvement of more than 50%.
  • The operating level most commonly used for audio equipment is +/- 15 volts.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (10)

Inputs

  • The Performer s800 is equipped with XLR inputs (8, 12) for a balanced connection to a preamp.
  • Full output power (2 x 285 W RMS into 4 ohms or 2 x 185 W RMS into 8 ohms) is performed at +6 dBu at the input.
  • For unbalanced connection with e.g. RCA output connect Pin 3 to Ground in the external connector.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (11) spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (12)

Slave Thru

  • The input is passively fed to the SLAVE THRU (9, 13) output for bi-wiring applications.

Trim

  • The input can be lowered with the TRIM switch (10, 14) from 0 dB to -5.5 dB in 0.5 dB steps.
  • This is helpful if you want to use multi-speaker sets or speakers in a bi-wiring application.
  • It allows to level speakers with different efficiency to equal loudness.

Bridge Mode

  • In bridge mode, only the left input is used. The right input and the trim switches are deactivated.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (13)

Speaker outputs

  • You can connect 4 or 8 ohms loudspeakers to the speaker outputs (11, 15) in stereo mode. In bridge mode, you can connect 8 ohms loudspeakers to the speaker outputs.
  • You can either use the ø4 mm cable hole (screwable) or the banana plugs of the gold-plated loudspeaker binding posts.
  • Make sure that you do not mix up the polarity of the speaker connections and that the power amplifier is switched off when you connect speaker cables.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (14)

Bridge Mode

The Performer s800 can be operated in bridge mode to combine both channel amps for maximum power (450 W RMS into at least 8 ohms). Only use the left input then.

  • Set the BRIDGE MODE (7) switch to ON.
    Warning: Power down the Performer s800 with the mains switch (5) before you activate the BRIDGE MODE switch.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (15)
  • In bridge mode, you only connect a single loudspeaker with at least 8 ohms to the Performer s800 power amplifier.
  • Use the positive binding post (+) of the left speaker output to connect to the positive (+) input of the speaker.
  • Use the positive binding post (+) of the right speaker output to connect to the negative (–) input of the speaker.

spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (16)

  • In bridge mode, both the Trim switch and the right input are deactivated.

Protection circuits

The Performer s800 has protection circuits against DC (direct current) voltage at the output and against overheating.

DC Protection

  • If DC is detected at the outputs, the Performer s800 automatically switches off. DC voltage can be an indication of a defective power stage.
  • The PROTECT LED (2) on the front indicates that the protection circuit is activated and the power stage has been switched off.
  • The Performer s800 does not automatically switch on again. It needs to be switched off manually with the main switch (5).
  • Wait at least one minute before switching the Performer s800 on again.
  • If the Performer s800 repetitively switches off due to a DC detection please contact your dealer.

Overheating protection circuit

  • At about 70° C at the heat sink, the Performer s800 will switch off. After the temperature has fallen below 55° C, the amplifier automatically switches on again. The TEMP LED (2) on the front indicates the overheating.

AMP CTL (Amplifier Control)

  • If you use the Performer s800 via AMP CTL with a SPL Phonitor x or SPL Director as a preamp, the Performer s800 can be switched between standby and operation together with the Phonitor x or the Director.
  • Therefore you only have to connect the AMP CTL jacks (6) with a 3,5 mm mono mini jack cable.
  • Warning: Use only SPL Phonitor x or SPL Director for amplifier control. Never connect other devices to the AMP CTL jack.spl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (17)

Specifications

Line Inputs & Line Outputs

  • Neutrik XLR, balanced, Pin 2 = (+)
  • Input impedance: 10 ohms
  • Input trimming: 0 dB to -5.5 dB in 0.5 dB steps
  • Input sensitivity: +6 dBu
  • Output impedance (Slave Thru) is defined by the connected device
  • Crosstalk: -110 dB (@1 kHz)

Speaker outputs

  • 2 pairs binding posts with ø4 mm cable hole (screwable) and banana plug; fully encapsulated

Output power

  • 2x 285 W RMS into 4 Ohm
  • 2x 185 W RMS into 8 Ohm
  • 1x 450 W RMS into at least 8 Ohm in bridge mode

Output voltage

  • 74 V Peak-to-Peak (stereo)
  • 180 V Peak-to-Peak (bridge)
  • 35 V RMS (stereo)
  • 86 V RMS (bridge)

Output impedance

  • < 0.031, 20 Hz to 20 kHz (stereo)
  • < 0,043, 20 Hz to 20 kHz (bridge)

Damping factor

  • > 300, 20 Hz to 20 kHz, at 8 ohms (stereo)
  • > 190, 20 Hz to 20 kHz, at 8 ohms (bridge)

Frequency response

  • 9 Hz to 100 kHz +0, –0,03 dB
  • < 9 Hz to 200 kHz +0, –3 dB

Signal-to-noise ratio

  • > 118 dB (wide-band, unweighted, referred to full power output)
  • > 123 dB (A-weighted)

Gain

  • 26 dB (stereo)
  • 32 dB (bridge)

Total harmonic distortion

  • < 0,03% at 1 kHz, at 185 W, 8 ohms
  • < 0,19% at 20 kHz, at 185 W, 8 ohms
  • < 0,011% at 1 kHz, at 450 W, 8 ohms
  • < 0,12% at 20 kHz at 450 W, 8 ohms

Internal Voltage

  • +/- 60 V

Power supply

  • Mains voltage: 230 V AC / 50 Hz; 115 V AC / 60 Hz
  • Fuses: 230 V: T 4 A; 115 V: T 8 A
  • Power consumption: max 900 VA
  • Idle power consumption: 40W
  • Standby power consumption: 0.3 W

Dimensions (incl. feet)

  • (WxHxD) 10.94 x 3.94 x 13 in (278 x 100 x 330 mm)

Weight

  • 28.22 lbs (12.8 kg), unit only
  • 30.87 lbs (14.0 kg), shippingspl-Performer-s800-Stereo-Power-Amplifier-FIG-1 (18)

Important Notes

  • Version 1.2 – 06 /2022
  • Developer: Bastian Neu
  • This manual includes a description of the product but no guarantee for specific characteristics or successful results.
  • Unless stated otherwise, everything herein corresponds to the technical status at the time of delivery of the product by SPL Electronics GmbH.
  • The design and circuitry are under continuous development and improvement.
  • Technical specifications are subject to change.
  • © 2022 SPL Electronics GmbH. This document is the property of SPL and may not be copied or reproduced in any manner, in part or fully, without prior authorization by SPL.
  • Sound Performance Lab (SPL) continuously strives to improve its products and reserves the right to modify the product described in this manual at any time without prior notice.
  • SPL and the SPL Logo are registered trademarks of SPL Electronics GmbH.
  • All company names and product names in this manual are the trademarks or registered trademarks of their respective companies.

Declaration of CE Conformity

  • The construction of this unit is in compliance with the standards and regulations of the European Community.

This User Manual is optimized for Acrobat Reader. Interactive buttons may not appear in other applications. Stereo Power Amplifier.

Documents / Resources

spl Performer s800 Stereo Power Amplifier [pdf] User Manual
Performer s800, Performer s800 Stereo Power Amplifier, Stereo Power Amplifier, Power Amplifier, Amplifier

References

Leave a comment

Your email address will not be published. Required fields are marked *