KUPPERSBERG logo

TECHNICAL PASSPORT

KUPPERSBERG EGS 600 Gas Electric Hob

EGS 600
GAS-ELECTRIC HOB

EGS 600 Gas Electric Hob

Dear customer,
We thank you and congratulate you on your choice!
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 3 This new carefully designed product, manufactured with the highest quality materials, has been carefully tested to satisfy all your cooking demands. We would the retore request you to read and follow these easy instructions which will allow you to obtain excellent results right from the start.
May we wish you all the very best with your modern appliance!

THIS APPLIANCE IS CONCEIVED FOR DOMESTIC USE ONLY. THE MANUFACTURER SHALL NOT IN ANY WAY BE HELD RESPONSIBLE FOR WHATEVER INJURIES OR DAMAGES ARE CAUSED BY INCORRECT INSTALLATION OR BY UNSUITABLE, WRONG OR ABSURD USE.

Warning icon INSTRUCTIONS FOR USE

INSTALLATION
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  All the operations concerned with the installation (electrical connection) must be carried out by qualified technicians, in terms with the standards in force, for specific instructions, kindly read the part reserved for the installation technician.

USE
GAS BURNERS (FIG. 1).
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The ignition of the gas burner is carried out by putting a small flame to the upper part holes of the burner, pressing and rotating the corresponding knob in an anti-clockwise manner, until the maximum position has coincided with the marker. When the gas burner has been turned on, adjust the flame according to need. The minimum position is found at the end of the anticlockwise rotation direction
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 In models with automatic ignition, operate the knob as described above, pressing simultaneously, the corresponding push-button. For models with automatic/simultaneous (with one hand) ignition, it is sufficient to proceed as described above using the corresponding knob. The electric, spark, between the ignition plug and the burner provides the ignition of the burner itself After ignition, immediately release the push-button and adjust the flame according to need.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 For models with a thermoelectric safety system, the burner is ignited as in the various cases described above, keeping the knob fully pressed on the maximum position for approximately 3/5 seconds. After releasing the knob, make sure the burner is actually lit.

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 2 NOTE:
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  we recommend the use of pots and pans with a diameter matching that of the burner, thus preventing the flame from escaping from the bottom part and surrounding the pot;
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 do not leave any empty pots or pans on the fire;
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 do not use any tools for grill cooking on Crystal hobs. When cooking is finished, it is also a good norm to close the main gas pipe tap and/or cylinder.

GAS
* with reduction grid

KUPPERSBERG EGS 600 Gas Electric Hob - fig 1

fast …………………………………………………………. Ø 18 x 24
semifast …………………………………………………. Ø 14x 18
auxiliary…………………………………………………. Ø 12x 14
fish* ………………………………………………………… Ø 18 X 30

Warning icon MAINTENANCE

Gas/Electrical
Prior to any operation, disconnect the appliance from the electrical system. For long-life to the equipment, a general cleaning operation must take place periodically, bearing in mind the following:
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  the glass, steel and/or enamelled parts must be cleaned with suitable non-abrasive or corrosive products (found on the market). A void chlorine base products (bleach, etc.);
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 avoid leaving acid or alkaline substances on the working area (vinegar, salt, lemon juice, etc. ). ;
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 the wall baffle and the small covers (mobile parts of the burner) must be washed frequently with boiling water and detergent, taking care to remove every possible encrustation. Dry carefully and check that none of the burner holes is fully or partially clogged;
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 the electrical parts are cleaned with a damp cloth and are lightly greased with lubricating oil when still warm;
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 the stainless steel grids of the working area, after having been heated, take on a bluish tint which does not deteriorate the quality. To bring colour back to its original state, use a slightly abrasive product.

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 2 NOTE
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Cleaning of the taps must be carried out by qualified personnel, who must be consulted in case of any fimctioning anomaly.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Check periodically the state of conservation of the flexible gas feed pipe. In case of leakage, call immediately the qualified technicians for its replacement.

INSTRUCTIONS FOR THE INSTALLER

Installation
This appliance is not provided with a combustion product discharge. It is recommended that it be installed in sufficiently aerated places, in terms of the laws in force. The quantity of air which is necessary for combustion must not he below 2. 0 m3/h for each kW of installed power.
See table of burner power.

Positioning
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The appliance can be fitted into a working area as illustrated on the corresponding figure. Before positioning the hob, fit the seal around the entire peripnery of the hole cut in the worktop

KUPPERSBERG EGS 600 Gas Electric Hob - fig 2

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 That the plant is fitted with an efficient earth connection, following the standards and law provisions in force.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The earth connection is compulsory in terms of the law. Should there be no cable and/or plug on the equipment, use suitable absorption material for the working temperature as well, as indicated on the matrix plate. Under no circumstance must the cable
reach a temperature above 50 °C of the ambient temperature. Should a direct connection to the network be required, it will be necessary to interpose an omni polar switch with minimum aperture between the 3 mm. contacts, dimensioned to bear the plate load and it must follow the standards in force (the yellow/green earth cable must not be interrupted by the switch). The plug or omni polar switch must be easily reached on the installed equipment.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  The manufacturers decline any responsibility in the event of noncompliance with what is described above and the accident prevention norms not being respected and followed.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 If the mains cable becomes damaged, replace it immediately with a cable or special cable set obtained from the manufacturer or from after sales service.

GAS CONNECTION
(Fig. 3) Connect the appliance to the gas cylinder or to the installation according to the prescribed standards in force, and ensure beforehand, that the appliance matches the type of gas available. Otherwise, see «Adaptation to various types of gas». Furthermore,
check that the feed pressure falls within the values described on the table: «User chacteristics».

Rigid/semirigid metal connection
Carry out the connection with fittings and metal pipes (even flexible pipes) so as to obtain counter stress the inner parts of the appliance.

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 2 NOTE
Token the installation has been carried out, check the perfect sealing of the entire connection system, by using a soapy solution.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 3

Adaptation to various types of gas
(Fig. 4) Should the appliance be preset for a different type of gas than that available, proceed as follows:
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 replace the injectors (Fig. 4) with the corresponding type of gas to be used (see table «User characteristics»).

KUPPERSBERG EGS 600 Gas Electric Hob - fig 4

Warning icon PRODUCT OVERVIEW

KUPPERSBERG EGS 600 Gas Electric Hob - fig 5

User interface

KUPPERSBERG EGS 600 Gas Electric Hob - fig 6

Reference Description
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 4 А. Zone select key
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 5 B. Child lock key
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 6 С. ON/OFF key
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 7 D. Power/Timer slider regulating key
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 8 E. Timer key

Heating zone Power

Heating Zone Max. Power
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 4 1200 W
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 9 1800/900 W
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 10 3000 W
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 11 1750 W

Warning icon PRODUCT FUNCTIONS

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The ceramic hob caters for all kind of cooking, with its radiant heat cooking zones and its electronic touch controls and multi-functions, making it the ideal choice for the modern family.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The ceramic hob is extremely user-friendly, durable and safe.

Warning icon  SPECIAL FUNCTIONS
Protection from over-heating
A sensor monitors the temperature in the cooking zones. When the temperature exceeds a safe level, the cooking zone is automatically switched off.
Residual heat indicator
When the hob has been operating for some time, there will be some residual heat. The letter “H” appears to warn you that it is too hot to touch the surface.
Auto Shutdown Protection
Auto shut down is a safety protection function for your ceramic hob. It shut down automatically if ever you forget to turn off your cooking. The default working times for various power levels are shown in the below table:

Power level 2-2 3-4 5 6-9
Default working timer (min) 360 300 240 90

Protection against unintended operation.
Protection against unintended operation.
If the electronic control detects a button being held down for approx 00 seconds it will switch off automatically.
The control sends out an audible error signal to warn the sensors have detected the presence of an object. The display will indicate an error code «ER03».
If the hob is still hot, the display will indicate «H».

BEFORE USING YOUR NEW CERAMIC HOB
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  Read this guide, taking special note of the ‘Safety Warnings’ section.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Remove any protective film that may still be on your Ceramic hob.

USING THE TOUCH CONTROLS

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The controls respond to touch, so you don’t need to apply any pressure.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Use the ball of your finger, not its tip.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 You will hear a beep each time a touch is registered.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Make sure the controls are always clean, dry, and that there is no object (e. g. a utensil or a cloth) covering them. Even a thin film of water may make the controls difficult to operate.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 7

Warning icon CHOOSING THE RIGHT

COOKWARE
Do not use cookware with jagged edges or a curved base.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 8

Make sure that the base of your pan is smooth, sits flat against the glass, and is the same size as the cooking zone. Use pans whose diameter is as large as the graphic of the zone selected. Using a pot a slightly wider energy will be used at its maximum efficiency.
If you use smaller pot efficiency could be less than expected.

Always centre your pan on the cooking zone.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 9

Always lift pans off the ceramic hob do not slide, or they may scratch the glass.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 10

Warning icon USING YOUR CERAMIC HOB
To start cooking
Only turn on two heating zone

  1. Place a suitable pan on the cooking zone that you wish to use.
    KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  Make sure the bottom of the pan and the surface Of the cooking zone are clean and dry.
  2. Touch the ON/OFF key for 2 sec- onds.
    KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  After power on, the buzzer beeps once, all displays show “ 0 “, indicating that the ceramic hob has entered the state of standby mode.
  3. According to the heating zone where the pan is placed, adjust heat setting by touching the slider regulating key (E) control.
    KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  If you don’t choose a heat setting within 20 seconds, the ceramic hob will automatically switch off. You will need to start again at step 2.
    KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 You can modify the heat setting at any time during cooking.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 11

Using Child Lock Function
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 You can lock the controls to prevent unintended use (for example children accidentally turning the cooking zones on).
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 When the controls are locked, all the controls except the OFF control are disabled.

To lock the controls
Simultaneously press the KUPPERSBERG EGS 600 Gas Electric Hob - symbol 12 key and the key KUPPERSBERG EGS 600 Gas Electric Hob - symbol 13.
The hob emits a beep and the indi- cator will show “Lo “.

To unlock the controls

  1. Make sure the hob is turned on.
  2. Simultaneously press the KUPPERSBERG EGS 600 Gas Electric Hob - symbol 12 key and the KUPPERSBERG EGS 600 Gas Electric Hob - symbol 13key.
  3. You can now start using your hob.

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 2 When the hob is in the lock mode, all the controls are disable except OFF, you can always turn the hob off with the OFF control in an emergency, but you shall unlock the hob first in the next operation.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 12

Using the Timer
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 You can set it to turn one cooking zone off after the set time is up.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 You can set the timer for up to 99 minutes.

  1. Select the relevant cooking zone which is working by touching the zone select key (A).
  2. Press the timer key(F) KUPPERSBERG EGS 600 Gas Electric Hob - symbol 8, the timer indicators will show “00”.
  3. Using the KUPPERSBERG EGS 600 Gas Electric Hob - symbol 12 илиKUPPERSBERG EGS 600 Gas Electric Hob - symbol 13, buttons, you can realize the setting of timing from 1 to 99 minutes.
  4. When the time is set, it will begin to count down after 10 seconds. The red dot next to power level indicator will illuminate indicating that zone has set timer.
    KUPPERSBERG EGS 600 Gas Electric Hob - symbol 14
  5. If you need to check the remaining time, you can operate step 1 and step 2 again.
  6. When cooking timer expires, the corresponding cooking zone will be switch off automatically. Other cooking zone will keep operating if they are turned on previously.
    KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The timer function only work when cooking is turned on.

CARE AND MAINTENANCE

Electric Warning Icon Warning
Always switch off the electricity supply before performing maintenance  work.
In the event of a fault,  contact customer services.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 15 Damaged power cables should be replaced by a competent person or qualified electrician.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 16 For domestic use only.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 17 Never place an empty pan on the hob as this will cause an error message to appear on the control panel.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 18 When a cooking zone has been on for a long time, the surface remains hot for some time afterwards so do
not touch the ceramic surface.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 19 For sealed foods, please do not heat them before opening removing the lid so as  to avoid any dangers of
explosion due to heating expansion.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 20 If the surface of the hob is cracked, disconnect from power supply to avoid any possibility of electric shocks.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 21 Do not place rough or uneven pans on the hob, as  they could damage the ceramic surface.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 22 Avoid banging pots and pans down on the hob. The ceramic surface is tough but not unbreakable.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 23 Do not put detergents or flammable materials beneath the hob.

Appliance cleanliness

Caution
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Avoid rubbing with any abrasive or with the base of the pans, etc, as this will wear the markings on the top of the ceramic hob over time.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1  Clean the ceramic hob on a regular basis to prevent the build up of food residue.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The appliance should be cleaned after use.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The surface of the ceramic hob may be easily cleaned in the following way:

Type of dirt Cleaning method Cleaning materials
Lime scale Apply white vinegar to the surface, then wipe it dry with soft cloth Special ceramic cleaner
Burnt-on stains Clean with damp cloth and dry it with a soft cloth Special ceramic cleaner
Light stains Clean with damp cloth and dry it with a soft cloth Cleaning sponge
ted plastics Use a scraper suitable for ceramic glass to remove residue Special ceramic cleaner

By means of a scraper immediately remove any aluminum foil bits, food spills, grease splashes, suger marks and other high sugar content food from the surface in order to avoid damaging the hob. Subsequently clean the surface with some towel and appropriate product, rinse with water and dry by means of a clean cloth. Under no circumstance should sponges or abrasive cloths be used, also avoid using aggressive chemical detergents such as oven sprays and spot removers.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 13

Warning icon TECHNICAL DATA

Power Supply V/Hz 220-240 В 50 Hz
Gas Pressure mbar G20 – 20 mbar
G30-28~ 30/37 mbar
External Dimensions HхDхW mm 110X520X590
NG (G20 20 mbar) LPG (G30 20- 30/37mbar)
Injector Dia (Ø) and kW Injector Dia. (Ø) and kW
Gas category Dia kW Dia kW
Rapid burner 1.14 2.5 0.81 2.5
Auxiliary burner 0.74 1.0 0.51 1.0
Gas Hob Power 4750 W
Ceramiac Hob Power 3000 W

SELECTION OF INSTALLATION EQUIPMENT

Cut out the work surface according to the sizes shown in the drawing. For the purpose of installation and use, a minimum of 5 cm space shall be preserved around the hole.
Be sure the thickness of the work surface is at least 30 mm. Please select heat-resistant work surface material to avoid larger deformation caused by the heat radiation from the hotplate. As shown below:

KUPPERSBERG EGS 600 Gas Electric Hob - fig 14

L(mm) W(mm) H(mm) D (mm) E (mm) B (mm) Х (mm)
590 520 110 56 560 490 50 min

Under any circumstances, make sure the ceramic cooker hob is well ventilated and the air inlet and outlet are not blocked. Ensure the ceramic cooker hob is in good work state. As shown below.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 2 Note: The safety distance between the hotplate and the cupboard above the hotplate should be at least 650 mm.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 15

A(mm) B(mm) C(mm) D E
650 50 min 20 min Air intake Air exit 5mm

Warning icon CLEARANCE

Warning
Good ventilation is required around the appliance for easier dissipation of heat and low power consumption.
Sufficient clearance is required around the appliance. The gap between the hob and any cupboard above it should be at least 750mm.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 16

KUPPERSBERG EGS 600 Gas Electric Hob - fig 17

Cut out worktop to the template dimensions with suitable equipment and seal the cut edge with appropriate sealant.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 18

Stretch out the supplied seal along the underside edge of the hob, ensuring the ends overlap.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 19

Note: For electrical connection see Technical and legal information section

Warning icon CONNECTING THE HOB TO THE MAINS POWER SUPPLY

Warning icon This hob must be connected to the mains power supply only by a suitably qualified person.
Before connecting the hob to the mains power supply, check that:

  1. the domestic wiring system is suitable for the power drawn by the hob.
  2. the voltage corresponds to the value given in the rating plate
  3. the power supply cable sections can withstand the load specified on the rating plate.

To connect the hob to the mains power supply, do not use adapters, reducers, or branching devices, as they can cause overheating and fire.
The power supply cable must not touch any hot parts and must be positioned so that its temperature will not exceed 75˚C at any point.
Check with an electrician whether the domestic wiring system is suitable without alterations. Any alterations must only be made by a qualified electrician.

KUPPERSBERG EGS 600 Gas Electric Hob - fig 20

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 If the cable is damaged or to be replaced, the operation must be carried out the by after-sale agent with dedicated tools to avoid any accidents.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 If the appliance is being connected directly to the mains an omni polar circuit-breaker must be installed with a minimum opening of 3mm between contacts.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The installer must ensure that the correct electrical connection has been made and that it is compliant with safety regulations.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The cable must not be bent or compressed.
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 The cable must be checked regularly and replaced by authorised technicians only.

Please note!
The following shall not be considered as defects of the Product

Induction and electric cooktops Sound of working of induction cooking zones at activation of increased power
Dark, visually non-luminous segment of the thermostat on a glass ceramic cooking zone
Discoloration of desktop surface when using the product

SERIAL NUMBER:

KUPPERSBERG EGS 600 Gas Electric Hob - fig 21

Manufacturers:
M&G HAUSGERATE GMBH
Potsdamer Str. 92 10785 Berlin
Tel: (030) 544 37 834 Fax: (030) 544 37 856
Factories-branches of the manufacturer:
Zhongshan Infinite Electrical Appliances Co. , LTD.
Unit 1, 3rd Floor, No. 1, Nanping Road, Xiaolan Town, Zhongshan City, Guangdong
Province, P. R. Chinа

Importers:
LLC «MG Rusland», 141400
Moscow region, Khimki, Butakovo, 4
The manufacturer reserves the right to make any changes to design, outside appearance and scope of supply of appliance.

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 24

KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 Kuppersberg
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 www.kuppersberg.ru
KUPPERSBERG EGS 600 Gas Electric Hob - symbol 1 info@kuppersberg.ru

Documents / Resources

KUPPERSBERG EGS 600 Gas Electric Hob [pdf] Instruction Manual
EGS 600, EGS 600 Gas Electric Hob, Gas Electric Hob, Electric Hob, Hob

References

Leave a comment

Your email address will not be published. Required fields are marked *