SRV7094-117 Expedition I Wood Stoves
“`html
Specifications
- Plating: Requires thorough cleaning before initial use
- Firebrick: Inspect regularly and replace if crumbly or if there
is a 1/4 inch gap between bricks - Baffle & Blanket Placement: Must be correctly positioned
for safe and efficient operation
Product Usage Instructions
Cleaning and Maintenance
Clean all fingerprints and oils from plated surfaces before
using the appliance for the first time. Failure to clean properly
can cause permanent markings on the plating. Once the plating is
cured, little maintenance is required. Wipe clean as needed.
Inspecting and Replacing Firebrick
- After the coals have cooled, remove old brick and ash from the
unit. - Follow the diagram instructions to lay out the new brick
set. - Install the bottom bricks first, followed by the rear and side
bricks. - Do not operate the appliance without firebrick.
Correct Baffle & Blanket Placement
WARNING: Improper baffle placement can cause
firebox damage and void the warranty. Ensure correct placement as
per the instructions.
Correct Position: Baffle Board and Ceramic
Blanket must be in contact with the back of the firebox and even
with each other in the front.
Incorrect Positions: Avoid situations where the
Ceramic Blanket and Baffle Board are not in contact with the back
of the firebox.
FAQ
Q: How often should I inspect and replace the firebrick?
A: Inspect the firebrick regularly and replace them if they are
crumbly or if there is a 1/4 inch gap between bricks.
Q: What happens if I do not place the baffle correctly?
A: Incorrect baffle placement can lead to firebox damage, poor
efficiency, and voiding of your warranty. Always ensure correct
positioning.
“`
Clean all the ngerprints and oils rom plated suraces BEFORE ring the appliance or the rst time. I not cleaned properly beore lighting your rst re, the oils can cause permanent markings on the plating.
Ater the plating is cured, the oils will not aect the nish and little maintenance is required. Wipe clean as needed.
6. Inspect Firebrick
· Frequency: After each ash removal
· By: Homeowner
Replace the rebrick i they become crumbly and/or i there is a 1/4 inch (6.35mm) gap between the bricks.
The rebox is lined with rebrick, which has exceptional insulating properties. Do not use a grate; simply build a re on the rebox oor. Do not operate appliance without rebrick. 1. After the coals have completely cooled, remove all old
brick and ash rom unit and vacuum rebox. 2. Remove new brick set from box and lay out to the
diagram shown in the instructions that come with the brick set or refer to the diagram on the service parts list at the end of this manual.
3. Lay bottom bricks in unit.
4. Install rear bricks on the top o the bottom bricks. Slide top o bricks under clip on back o rebox wall and push bottom of bricks back.
5. Install side bricks. Slide top o brick under clips on side o rebox and push the bottom o the brick until it is ush with the side of the unit.
D. Correct Bafe & Blanket Placement
WARNING
Fire Risk. Firebox damage due to improper bafe placement is not covered by warranty. Operate the wood burning appliance with the bafe in the correct position only.
Not doing so could result in: · Reduced eciency · Overheating the chimney · Overheating the rear o the rebox · Poor performance Ensure correct bafe placement and replace bafe components if damaged or missing.
NOTE: These are generic drawings and may not represent your specic model.
CORRECT POSITION
Baffle Retainer Bracket
Ceramic Blanket
Back of Firebox
Baffle Board
Ceramic Blanket and Bafe Board MUST be in contact with the back o the rebox and even with each other in the front. Figure 19.1 – Correct Bafe and Blanket Positions
INCORRECT POSITIONS
Ceramic Blanket and Bafe Board are NOT in contact with the back o the rebox.
Ceramic Blanket is NOT in contact with the back o the rebox and NOT even with the Bafe Board in the ront.
Ceramic Blanket
Back of Firebox
CAUTION
The bafe boards are FRAGILE. Use extreme caution when loading rewood to prevent: · Cracking, breaking or damaging the bafe boards DO NOT operate the appliance without bafe boards
NOTE: A missing, damaged or improperly positioned bafe is dangerous and may cause damage and poor eciency. It will also void your warranty.
Baffle Board Ceramic Blanket is bunched up at the back o the rebox and NOT even with the Bafe Board in the ront.
Figure 19.2 – Incorrect Bafe and Blanket Positions
19
7102-803E
04/23
Documents / Resources
 |
QUADRA-FIRE SRV7094-117 Expedition I Wood Stoves [pdf] Instructions SRV7094-117 Expedition I Wood Stoves, SRV7094-117, Expedition I Wood Stoves, Wood Stoves, Stoves |
