B092LK8TST 6 Light Modern Farmhouse Chandelier for Kitchen Island
WARNING (To reduce the risk of fire, electric shock, or personal injury):
- We suggest installation by a licensed electrician.
- Please read the instruction carefully and save it as you may need it at later time.
- Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the “OFF” position. - Mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all side. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.
- Make sure that the ceiling or wall can stand the weight of the lamp before installation.
- Make sure the voltage you are using is 120V. The maximum wattage is 40W per bulb.
- Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.
- When replacing bulb, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.
- The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution and care must be used with any electrical products.
IMAGE FOR FINISHED PRODUCT
TOOLS REQUIRED (NOT INCLUDED)
Before starting assembly and installation please prepare the needed tools as below picture 
PARTS TYPE & QTY INCLUDING
ACCESSORIES & QTY ENCLOSED
(A) Wire connector (3)
(B) Anchor (4)
(C) Mounting screw (2)
(D) Wood screw (4)
(E) Mounting plate assembly (1)
(F) Green ground screw (1)
(G)Knob nut (2)
(H)Canopy (1)
(I) Loop (4)
(J) Quick link (2)
(K) Stem
(L) Glass shade (6)
(M) Cover (6)
(N) Iron frame (1)
ASSEMBLY & INSTALLATION INSTRUCTIONS:
- Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.
- Make pre-installation
Step A1: According to your desired hanging height, choose and use the stems (K). Carefully thread the fixture wires through the stem (K), then screw the stem (K) onto the iron frame (N).
Step A2: Attach the quick link (J) on the stem (K) to the loop (I) of the canopy (H). - Turn off power
Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
A) Go to the main fuse, or circuit breaker, box in your home. Place the main power switch in the “OFF” position.
B) Place the wall switch in the“OFF” position. - Make installation
Step B1: Unscrew the ball knob (G) from mounting plate assembly (E).
Step B2: Attach the mounting plate assembly (E) to ceiling with the mounting screws (C), anchors (B) and wood screws (D).
Step B3: If needed, shorten the length of fixture wires. At this point, the remaining wire length measured above the mounting plate assembly (E) is at least 6″.
Step B4: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.
Connect ground wires according to the below chart 
Connect wires according to the below chart
| Connect Black or Red Supply Wire to: | Connect White Supply Wire to: |
| Black | White |
| *Parallel cord ( round & smooth) | *Parallel cord ( square & ridged ) |
| Clear,Brown,Gold or Black without tracer | Clear,Brown,Gold or Black with tracer |
| Insulated wire ( other than green ) with copper conductor | Insulated wire ( other than green ) with silver conductor |
*Note: When parallel wires (SPT & SPT II) are used. The neutral wire is square shaped or ridged and the other wire will be round in shape or smooth (see illus.)
Twist wires together with plastic wire connector until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step B5: Raise canopy (H) to ceiling and secure canopy (H) in place with ball knobs (G) onto the pre-assembled threaded nipple on mounting plate assembly (E).
Step B6: Install bulbs (not included) (Please do not exceed the maximum wattage recommended on the socket.)
Then carefully place the glass shade (L) on the cover (M).
Check everything is already installed properly, then you could turn on the light. Enjoy!
CLEANING.
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool or abrasive paper.
ORDERING PARTS.
Keep this sheet for future reference, and in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase. Be sure to use exact wording from illustration when ordering parts.
Documents / Resources
 |
PHOSANT LIGHTING B092LK8TST 6 Light Modern Farmhouse Chandelier for Kitchen Island [pdf] Instruction Manual B092LK8TST 6 Light Modern Farmhouse Chandelier for Kitchen Island, B092LK8TST, 6 Light Modern Farmhouse Chandelier for Kitchen Island, Farmhouse Chandelier for Kitchen Island, Chandelier for Kitchen Island, Kitchen Island |
