Hudson Valley Lighting Troy Lighting
Mitzi Corbett Lighting
B6018-TBK Troy Lighting Tall Wall Sconce Gridley 2 Light
WARNING/CAUTION
- DISCONNECT POWER BEFORE RE-LAMPING OR WIRING THE FIXTURE. READ ALL INSTRUCTIONS COMPLETELY BEFORE STARTING INSTALLATION.
- TO AVOID THE RISK OF FIRE OR SHOCK, FIXTURE MUST BE INSTALLED IN COMPLIANCE WITH ALL APPLICABLE NATIONAL AND LOCAL ELECTRICAL/BUILDING CODES. THE INSTALLATION ANDMAINTENANCE OF THIS UNIT SHOULD BE COMPLETED BY A LICENSED ELECTRICIAN OR CERTIFIED FACTORY TRAINED TECHNICIAN.
- CALIFORNIA PROP 65: THIS LIGHTING FIXTURE CONTAINS CHEMICALS KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS, AND/OR OTHER REPRODUCTIVE HARM.WASH HANDS AFTER USE.
- UNPACK FIXTURE, PARTS AND PARTS BAG(S) BEFORE DISCARDING THE CARTON. MAKE CERTAIN THAT ALL PARTS ARE FOUND. INSPECT THE FIXTURE PRIOR TO INSTALLATION FOR ANYDAMAGE. HVLG DOES NOT PAY OR REIMBURSE ELECTRICIAN FEES. FIXTURE MAY NOT BE RETURNED ONCE IT HAS BEEN INSTALLED. SEE WARRANTY FOR EXCEPTIONS.
- PLEASE CLEAN WITH A SOFT, DRY CLOTH ONLY! DO NOT USE CLEANSERS.
TROY LIGHTING
GRIDLEY B6022 Installation Instructions
| PART(S) | REPLACEMENT PART NAME | NUMBER |
| A,B,C,D,E,F | HARDWARE KIT | HDW-B6022 |
| G | CAP NUT | CPN-B6013 |
| H | FIXTURE MOUNTING SCREW | SCR-M |
| L | GLASS A | GLS-B6022-A |
| M | GLASS B | GLS-B6022-B |
FIXTURE INSTALLATION
- Loosen the MOUNTING SCREWS (H) to remove the FRAME (K) from the FIXTURE ASSEMBLY (I) .
- Determine the location for the lamp. Using the mounting plate as a template, mark the location of theholes for the WALL ANCHOR (F).
- Drill the appropriate size holes for the WALL ANCHOR (F). (the holes should be slightly smaller thanthe size of the anchors.) Install the wall anchors to the hole.
- Attach the MOUNTING PLATE (A) onto the junction box using the MOUNTING SCREWS (B). Thisfixture is designed to be mounted on standard junction box. The junction box must be securely mounted to the structure of the building. Screw in the WOOD SCREW (E) to the WALL ANCHOR (F).
- Attach the Ground wire (Green) to the ground inside the outlet box (Generally green or bar copperwire) or the GROUND SCREW (C) on the MOUNTING PLATE (A). NEER CONNECT GROUND WIRE TO “HOT” WIRE FAILURE TO FOLLOW THIS COULD RESULT IN SERIOUS INJURY OR DEATH
- Connect the white fixture lead to the neutral (Generally white) wire in the outlet box. Fasten the wirestogether with an approved fastener (WIRE NUT) (D). Starting 1″ below the fastener, tightly wrap the connection with electrical tape so that the connections seals the end of the fastener. MAKE SURETHERE ARE NO EXPOSED WIRE OF STRANDS THAT COULD CAUSE A DANGEROUS SHORT CIRCUIT
- Connect the black fixture leads to the hot (Generally black) wire in the junction box. Fasten the joinedwires same as previous step. NEER REERSE HOT AND NEUTRAL WIRES. FAILURE TO FOLLOWTHIS COULD RESULT IN SERIOUS INJURY OR DEATH
- To prevent water from flowing into the outlet box, put a bead of weatherproof caulking or siliconesealant around the inside edge of the back. DO NOT PLUG THE DRAIN HOLE (N)
- Attach the FIXTURE ASSEMBLY (I) to the MOUNTING PLATE (A) and secure with the CAP NUT (G).
- Screw the BULB (J) (not included)up into the SOCKET of the fixture. THIS FIXTURE IS RATED FOR MAX WATT TYPE T LED LAMP. DO NOT EXCEED THE RECOMMENDED WATTAGE
- Attach the FRAME (K) to the FIXTURE ASSEMBLY (I) and secure with the FIXTURE MOUNTINGSCREWS (H).
- Install the GLASS A, B (L, M) to fixture. pushing the clip to hold the glass.
- Restore power to the outlet at the breaker or fuse box.
Documents / Resources
 |
HUDSON VALLEY B6018-TBK Troy Lighting Tall Wall Sconce Gridley 2 Light [pdf] Instruction Manual B6018-TBK Troy Lighting Tall Wall Sconce Gridley 2 Light, B6018-TBK, Troy Lighting Tall Wall Sconce Gridley 2 Light, Wall Sconce Gridley 2 Light, Gridley 2 Light |
