Heat-Line 1123 Retro-Line
Advanced Internal Water Supply Pipe System. Heat-Line is a complete pipe system supplied with the Retro-Line heating cable system factory installed inside a 75 PSI, CSA-approved polyethylene water pipe for new pipe installations.
Features & Benefits
- The only manufactured, self-regulating heating cable factory installed in the pipe
- Available in 1-inch ID and 1¼ inch ID, 75 PSI polyethylene pipe
- Available in a plug-in GFCI model or hard wire cord-set model depending on the application
- Customizable for various application requirements
- The length of the heating cable can be adjusted (shortened) on the job site using extracting the cable through the plumbing fitting
- Available in common lengths and long lengths
- The heating cable is rigid enough to stay in place within the entire length of the pipe
- Labour savings – no need to excavate below the frost line or blast rock
- Fully serviceable, can easily be removed if necessary
- Will never melt or overheat, even if the pipe is dry
- Proven in -40ºF weather above ground with ¾ inch polyethylene insulation
- For more Features and Benefits Common
- For all Heat-Line systems, refer to page 6.
Specifications
- CSAus approved (Canada and USA) LR85446
- Approved for potable drinking water
- Certified Usage Type P Canada
- Installation Type A USA
- Self-regulating/conductive polymer heating cable
- Fluoropolymer outer jacket
- Standard wattage 3 W/ft @ 50ºF (10 W/m @ 10ºC), special wattage available
- Available in 120V and 240V
- Max lengths 120V – 230 ft, 240V – 300 ft
- Available with either a GFCI plug or CS hard wire connection
- Engineered proprietary end seal technology
- Standard warranty of 5 yrs with optional 10 yrs
- Applications
- New water supply lines requiring freeze protection
- Potable water supply 75 PSI or less
- Rural home and business water supply lines
- Lake homes and cottages/cabins
- Lake/river water source
- Wells
- Farms, agriculture
Complete Freeze Protected
Polyethylene Pipe System
The Heat-Line system is supplied in a pre-determined length with the self-regulating heating cable already installed inside 75 PSI, CSA-approved polyethylene pipe. Philmac plumbing fitting was also supplied.
Easy Installation
Just unroll the pipe and interface to plumbing fittings as necessary as you would with any non-heated poly.
Reliable Above Ground
Heat-Line has been proven to keep water from freezing at -40ºC/F when installed above ground with ¾-inch thick pipe insulation. No need to blast rock to bury the pipe.
Energy Efficient
Save up to 80% in energy consumption when combining thermostats and insulation. The thermostat and timers are optional with the heat line. They can be used to duty cycle the heating cable in an on/off operation making it more energy efficient. Heat-Line is safe to insulate and will make the heating cable operate more efficiently and reliably when used.
Requirements
Heat-line orders require the length of the system and the size of the pipe. The maximum system length of 240 volts is 300 feet.
Emergency Systems
In many applications, Heat-Line is ordered for new builds where the water system is not yet complete. Heat-Line is ordered with insulation and installed on the ground until the following year when the trench can be dug and the same Heat-Line system buried.
Energy Efficient
With its self-regulating heating cable. Heat-Line can be the most energy-efficient heating cable available, providing you insulate and add a thermostat.
Fully Serviceable
The Heat-Line system is a fully serviceable product. Should you need to remove the heating cable, simply remove the plumbing tee fitting and pull out the heating cable.
Customizable
In many cases, custom lengths can be ordered such as 80 feet of heating cable installed inside 100 feet of pipe.
Product Code Guide
NOTE: The nominal power output of the Heat-Line system is 3 W/ft 50°F (10 W/m @ 10°C). Only available in Drinking Water Safe Fluoropolymer outer heating cable jacket
Accessories
- HLJ-STAT 120V plug-in thermostat (GFC)
- HLA-120 120V plug-in thermostat (GFC)
- GFA-STAT 120/240V hard wire thermostat GFEP (CS)
- TIMER-120P 120V plug-in timer (GFC)
- TIMER-240P 240V plug-in timer (GFC)
- TIMER-CS 120/240V hard wire timer (CS)
- MA-10 120/240V GFCI/ELCI (CS)
- INSUL-1.00 Insulation sleeve for 1 inch ID pipe (1 5/8 inch ID, 6 ft long)
- INSUL-1.25 Insulation sleeve for 1 ¼ inch ID pipe (1 7/8 inch ID, 6 ft long)
- HLP-TAPE Tape for insulation sleeve butt joints (100 ft)
- WARRANTY Extended 10-year limited warranty
Typical Cross Section
Documents / Resources
 |
Heat-Line 1123 Retro-Line [pdf] Installation Guide 1123 Retro-Line, 1123, Retro-Line, Line |
